Plumbing Basics: A Prerequisite for Installing a Bathtub
Plumbing Basics: A Prerequisite for Installing a Bathtub
Blog Article
We have stumbled on this article pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the net and concluded it made good sense to write about it with you in this article.
Setting up a bath tub isn't exactly rocket science, however it does need strong plumbing, carpentry, and also often, tiling skills. Replacing an old bathtub with a brand-new one is likewise a reasonably difficult project. If the old tub is readily available, the job can move rapidly; if you have to open a wall surface to remove the old bathtub and position the new tub, the task is much harder. In either situation, the project is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub and also set in the new one. Make sure you have actually qualified on your own for the work as well as fit attempting it. Rather than working with a specialist to take control of a halfway-completed project, it is much better to think about utilizing one prior to you start. Opportunities are you may need a professional plumber to make tube connections.
This write-up will certainly help you mount a new bath tub in your shower room if you have actually currently bought a new tub and also don't require to change the arrangement of your previous water pipes.
Your devices and product checklist should comprise the following:
Preparing for the Installation
Firstly, the supporting structure provided with the bathroom needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps system to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps utilizing 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you make use of every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its last position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, then the first thing you should do is detach the supply of water. After doing so, activate the faucets to drain any water continuing to be in the system. The process of getting rid of the existing faucets can be rather troublesome because of the restricted gain access to that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a fabric ready for the remaining water that will originate from the pipes. As soon as the supply pipelines have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleaned up of any kind of old sealing substance.
Before going on to fit the brand-new taps, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Utilizing both wood boards under its feet, place the bath tub in the called for position. The wooden boards are useful in equally spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 little points.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the tub until the spirit level reads level.
To install taps, fit the bottom of the outermost flexible faucet adapter to the proper supply pipe by making a compression join; after that do the very same for the various other tap.
Turn on the water and also inspect all joints as well as brand-new pipework for leakages and tighten them if required. Load the tub and likewise check the overflow electrical outlet and the normal outlet for leakages.
Finally, fix the bathroom paneling as explained in the supplier's user's manual. Tiling as well as sealing around the tub ought to wait until the bathtub has actually been used a minimum of once as this will certainly resolve it into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washing machines remain in location in between the faucet as well as the sink. Protect the tap in position with the supplier provided backnut. Once the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal tap ports. The former kind must be connected to the tap ends first, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to split a stiff seal, triggering the water to permeate the wall surface between the bath as well as the tiling, resulting in difficulties with dampness and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures as well as installations. They are offered in tubes as well as cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill the bathtub with water prior to sealing, to permit the activity experienced when the tub remains in use. The sealant can crack fairly very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise conveniently available on the marketplace. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that article on Installing A Bathtub while doing a search on the web. Do you know somebody who is in to the subject? Take a moment to share it. I love reading our article about How to Install a Bathtub Yourself.
Schedule Estimate Report this page